LM-6601
12.1” 2nd LCD Monitor
User’s Manual
Rev. Original
I. FEATURES
·
12.1” LCD monitor with tilt adjust for 2nd display attached to FT series
POS system
·
·
Spill proof and easy maintenance structure allowing easy cleaning
High quality TFT LCD panel with scaling up function for full screen
display
·
·
·
·
Resolution: 1024 x 768
Color depth: 262,144 colors
Super VGA interface
Powered through interface cable
FCC NOTICE
This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance
with the instructions manual, may cause interference to radio communications. It has been tested and found to comply with limits
for a Class A digital device pursuant to subpart J of Part 15 of FCC Rules, which are designed to provide reasonable protection
against interference when operated in a commercial environment. Operation of this equipment in a residential area is likely to cause
interference in which case the user at his own expense will be required to take whatever measures to correct the interference.
WARRANTY LIMITS
Warranty will terminate automatically when the machine is opened by any person other than the authorized
technicians. The user should consult his/her dealer for the problem happened. Warranty voids if the user does not follow the
instructions in application of this merchandise. The manufacturer is by no means responsible for any damage or hazard caused by
improper application.
ABOUT THIS MANUAL
This manual assists the user to utilize the LCD Monitor LM-6601. Thos series provides adjustable robust
construction for 12.1” LCD display with maximum resolution of 1024 x 768 pixels and 262,144 colors. It is powered by the host FT
series system through the interface cable.
The manufacturer of the LM-6601 series heartily apologizes to the user for reserving the right to change or to modify
this manual without notice due to the rapid and constant progress and improvement on science and technology. The user may
Ó Copyright Posiflex Technologies, Inc. 2008
TRADE MARKS AND SERVICE MARKS
POSIFLEX is a registered trademark of Posiflex Technologies, Inc..
Other brand and product names are trademarks and registered trademarks and service marks of their respective owners.
P/N: 19050903010
Part 1
V. HARDWARE INSTALLATION
A. VGA Port Power Preparation
1. Inquire for technical support from your dealer to set the power support in
the VGA port of the FT system following the relevant Technical Manual
of the FT system. Please note that once the VGA port is no longer to be
occupied by the LM-6601, this power support must be discontinued!
B.
Fix Bracket onto LM-6601
2. Unfold down the semi-circular base tongue of the
LM-6601 main unit and apply the L shape bracket
on this base tongue. Use the 2 screws in the
accessory bag to fix the bracket over the base
tongue as circled in the right picture. Note that the
slots for the screws on the bracket allow some
adjustment on position of LM-6601 for application.
C.
Open Back Cover & Pole Cover of FT System
3. Refer to the User’s Manual of the FT system
about “INSTALLING BASE MOUNT KIT” to
open back cover and remove the 2 arrowed
screws to remove the pole cover. Preserve the 2
screws for the next step.
D.
Install LM-6601 to FT System
4. Install the slender part of the L shape bracket to the hole for pole cover
and screw it to top
cover of FT base
tightly at the arrowed
holes as in the left
picture and result is
shown at the right.
E.
Cable Connection
5. Connect the VGA cable that has both 3 x 5 D sub male ends to VGA port
at rear of LM-6601 and the VGA port of host system. Screw in the cable
to connectors at both ends.
F.
Driver Installation
6. There is no need to install driver for use of LM-6601. However, the
supported display modes are tabulated at last part of this manual
Part 3
VI. APPLICATION
A.
TILT ANGLE ADJUST
The tilt angle of LM-6601 can be easily adjusted against a set of friction
hinge. Just turn the panel at will.
B.
Power & OSD buttons
“OSD” button: To enter OSD setup menu, or to perform the function
selected in OSD operation.
“NEXT” button: To select next item of option functions.
“” “” button: To increase setting.
“” “” button: To decrease setting.
“” “” button: To turn the monitor power ON/OFF. The monitor can be
turned OFF only when there is video signal and can be turned ON only
when there is video signal and after the “Turn Off Panel” message
vanishes. The default status is set to ON when power is supplied unless
manually turned OFF. Since this button controls only the display power
but not the display controller, please try disconnect the VGA cable once
unfortunately the screen display goes into a mess.
C.
OSD functions
Press “OSD” button with a normal display on the screen to activate the
OSD functions (On Screen Display adjustment). The OSD window will pop up
on the screen. On top part of this window is a Posiflex logo with the OSD
firmware version indicated to its lower right. Below this area is a row of icons
for main OSD menu. Below the main menu is a group of icons for submenu
that corresponds to one icon selected in the main menu. An analysis of the
video signal on resolution and refresh rate will be displayed at the bottom.
Applicable icons in the main menu and its subsequent menus are explained
below.
“MAIN MENU”: There are in total 5 icons in this menu:
. One
of the 5 icons will be displayed in inverted color to indicate its relationship
with the submenu below. Pressing “NEXT” button will shift the selected icon
one by one from left to right and then wrap around to the most left. Press
“OSD” button to enter the selected sub menu. If there is no button for OSD
setting is pressed within a period of time (about 5 seconds to 1 minute as
programmed) the OSD window will disappear with all the adjusted parameters
saved. Explanations on items in sub menu are as below.
Part 4
“BRIGHTNESS / CONTRAST ADJUST SUBMENU”: There are 3
icons in this submenu: . Press “OSD” button to select item or return
to main menu. Press “NEXT” button to select among brightness, contrast and
exit.
“BRIGHTNESS ADJUST”: When this item is selected, there
will be only the brightness icon with an adjustment indication bar under
it between the main menu area and the video signal mode. Press “+”
button to increase brightness. Press “-” to decrease. Press “OSD” button
to save the current setting and return to “Brightness/Contrast submenu”.
“CONTRAST ADJUST”: When this item is selected, there will
be only the contrast icon with an adjustment indication bar under it
between the main menu area and the video signal mode. Press “+”
button to increase contrast. Press “-” to decrease. Press “OSD” button
to save the current setting and return to “Brightness/Contrast submenu”.
“EXIT”: Return to “Main menu”.
“COLOR ADJUST SUBMENU”: There are 4 icons in this submenu:
Press “OSD” button to select item or return to main menu.
Press “NEXT” button to select among auto color adjust, auto RGB reset, Color
balance adjust and exit.
“AUTO COLOR ADJUST”: Upon an “OSD” button press on
this icon the monitor will perform an automatic color adjustment and
exits the OSD window leaving 2 icons below at center of the screen.
Press “NEXT” button to switch the selection. Press “OSD” button to
make the choice.
“ACCEPT”: Accept the adjustment setting.
“REJECT”: Decline the adjustment setting and return to
previous setting.
“AUTO RGB RESET”: Upon an “OSD” button press on this
icon the monitor will perform an automatic RGB reset and exits the
OSD window leaving 2 icons below at center of the screen. Press
“NEXT” button to switch the selection. Press “OSD” button to make
the choice.
“ACCEPT”: Accept the reset result.
“REJECT”: Decline the reset and return to previous
setting.
“COLOR BALANCE ADJUST”: When this item is selected,
there will be 7 icons in this item:
between main
menu area and the video signal mode. Press “OSD” button to select an
item or return to color adjust submenu. Press “NEXT” button to select
among separate color adjust, 4200K, 5000K, 6500K, 7500K, 9300K
and exit.
Part 5
“SEPARATE COLOR ADJUST”: When this item is
selected, there will be 3 adjustment indication bars between the
main menu area and the video signal mode. Press “NEXT”
button to select among the 3 colors Red, Green and Blue
respectively. Press “+” button to intensify that color. Press “-” to
reduce. Press “OSD” button to save the current setting and
return to “Color balance adjust submenu”.
“4200K”: Pressing “OSD” button on this icon will set the
color balance to a color temperature of 4200 degrees Kelvin.
“5000K”: Pressing “OSD” button on this icon will set the
color balance to a color temperature of 5000 degrees Kelvin.
“6500K”: Pressing “OSD” button on this icon will set the
color balance to a color temperature of 6500 degrees Kelvin.
“7500K”: Pressing “OSD” button on this icon will set the
color balance to a color temperature of 7500 degrees Kelvin.
“9300K”: Pressing “OSD” button on this icon will set the
color balance to a color temperature of 9300 degrees Kelvin.
“EXIT”: Return to “Color adjust submenu”.
“EXIT”: Return to “Main menu”.
“GEOMETRY ADJUST SUBMENU”: There are 6 icons in this
submenu:
Press “OSD” button to select item or return to
main menu. Press “NEXT” button to select among auto geometry adjust,
horizontal size, phase, horizontal position, vertical position and exit.
“AUTO GEOMETRY ADJUST”: Upon an “OSD” button press
on this icon the monitor will perform an automatic geometry adjustment
and exits the OSD window leaving 2 icons below at center of the screen.
Press “NEXT” button to switch the selection. Press “OSD” button to
make the choice.
“ACCEPT”: Accept the adjustment setting.
“REJECT”: Decline the adjustment setting and return to
previous setting.
“HORIZONTAL SIZE”: When this item is selected, there will
be only the horizontal size icon with an adjustment indication bar under
it between the main menu area and the video signal mode. Press “+”
button to increase horizontal size. Press “-” to decrease. Press “OSD”
button to save the current setting and return to “Geometry adjust
submenu”.
“PHASE”: When this item is selected, there will be only the
phase adjust icon with an adjustment indication bar under it between
the main menu area and the video signal mode. Press “+” or “-” button
to adjust the pixel synchronization phase for best picture display. Press
“OSD” button to save the current setting and return to “Geometry
Part 6
adjust submenu”.
“HORIZONTAL POSITION”: When this item is selected, there
will be only the horizontal position icon with an adjustment indication
bar under it between the main menu area and the video signal mode.
Press “+” or “-” button to shift the screen display to right or left. Press
“OSD” button to save the current setting and return to “Geometry
adjust submenu”.
“VERTICAL POSITION”: When this item is selected, there
will be only the vertical position icon with an adjustment indication bar
under it between the main menu area and the video signal mode. Press
“+” button to shift up the screen display. Press “-” to shift down. Press
“OSD” button to save the current setting and return to “Geometry
adjust submenu”.
“EXIT”: Return to “Main menu”.
“TOOLS SUBMENU”: When this item is selected, there are 5 icons in
this submenu:
. Press “OSD” button to select item or return
to main menu. Press “NEXT” button to select among OSD submenu, reset to
default, phase, smoothness / sharpness adjust, mode select and exit.
“OSD SUBMENU”: When this item is selected, there are 4 icons
in this submenu:
Press “OSD” button to select item or
return to main menu. Press “NEXT” button to select among OSD time,
OSD horizontal position, OSD vertical position and exit.
“OSD TIME”: When this item is selected, there will be
only the OSD time icon with an adjustment indication bar under
it between the main menu area and the video signal mode. Press
“+” or “-” button to adjust the waiting time for OSD operation
before OSD termination between 5 to 60 seconds. Default is 30
seconds. Press “OSD” button to save the current setting and
return to “OSD submenu”.
“OSD HORIZONTAL POSITION”: When this item is
selected, there will be only the vertical position icon with an
adjustment indication bar under it between the main menu area
and the video signal mode. Press “+” button to shift OSD
window right. Press “-” to shift left. Press “OSD” button to save
the current setting and return to “OSD submenu”.
“OSD VERTICAL POSITION”: When this item is
selected, there will be only the vertical position icon with an
adjustment indication bar under it between the main menu area
and the video signal mode. Press “+” button to move OSD
window downward. Press “-” to go upward. Press “OSD” button
to save the current setting and return to “OSD submenu”.
“EXIT”: Return to “Tools submenu”.
Part 7
“RESET TO DEFAULT”: Pressing “OSD” button on this icon
will set all parameters back to the status when the monitor left factory.
“SMOOTHNESS / SHARPNESS ADJUST”: When this item is
selected, there will be only the smoothness / sharpness adjust icon with
an adjustment indication bar under it between the main menu area and
the video signal mode. Press “+” button to increase smoothness of
display (decrease sharpness). Press “-” to go the other way. Press
“OSD” button to save the current setting and return to “OSD submenu”.
“MODE SELECT”: Pressing “OSD” button on this icon will
have no effect at all if the display mode is not one of the confusing
modes. The confusing modes here mean 640 x 400 or 720 x 400 in
display resolution as both mode have refresh rate of 70Hz, horizontal
frequency of 31.5KHz and pixel frequency of 31.5MHz making it
impossible for automatic select. These modes are not used in normal
Windows display.
“EXIT”: Return to “Main menu”.
“EXIT”: Exit OSD setup with all adjustments saved.
Part 8
VII. SUPPORTED DISPLAY MODES
For video signals beyond the supported display modes, there will be a
message “Out Of Range” on middle of screen. Maximum supported color
depth is 18 bits or 262,144 colors. Supported display modes are as in the table:
Display Resolution
640*400
Refresh Rate (Hz) Horizontal Frequency (KHz)
70
60
72
75
70
56
60
72
75
60
70
75
31.5
31.5
37.9
37.5
31.5
35.1
37.9
48.1
46.9
48.4
56.5
60
640*480
720*400
800*600
1024*768
Part 9
T31454
警告使用者
這是甲類的資訊產品，在居住的環
境中使用時，可能會造成射頻干
擾，在這種情況下，使用者會被要
求採取某些適當的對策。
Part 10
|