Model：PM15LCD
4:3 DIGITAL LCD-Monitor
15 LCD MONITOR
OPERATING MANUAL
1. PREFACE
Thank you for buying this TV ! Please read this manual thoroughly before operating the monitor.
Make sure the monitor was not damaged in transit. Should the monitor is damaged, do no install
it and contact your dealer. Check that you have all the accessories according to the model.
2. SAFETY PRECAUTIONS
Preparation
Put the monitor on a stable surface.
Do not place any material on the monitor.
Minimum distances
10cm
10cm 5cm
20cm
If you have a wall mount, check that it is steady
Do not block or cover the ventilation openings on the monitor
Connexion cables
Power cord and cables must be properly routed and protected to prevent
people from stepping on them and causing the monitor to fall.
2
Heating sources and humidity
Keep the monitor dry and away from humidity.
Keep the monitor away from heat sources
Cleaning and maintenance
Unplug the monitor before cleaning it. Do not use solvents or liquids
to clean the monitor.
Only clean the monitor with a soft and dry cloth.
In case of troubleshooting, do not use spare parts other than those
suggested by
the manufacturer. Using inadequate spare parts can lead to electric
shocks, short-circuits fire or other incidents.
Departure in holidays
Unplug the LCD during lighting storms or when unused for long periods
of time.
3
3. FRONT BACK/SIDE CONNECTIONS OF LCD
Front View
1.Press“POWER” Switch on the LCD TV when
at standby mode or vice versa.
2.Press“UP”or “DOWN”to select option in
menu
3.Press“V+”or “V-”to increase or decrease
the sound level.
4.Press “MENU”to bring up the main menu to
the screen
5.Press“SOURCE”to select the input source
Back View and Control Connections
1.DC 12V IN: DC input socket
2.VGA: Connect the PC-RGB output jack of PC
3.YPbPr: Connect the DVD YPbPr output jack of
the DVD Player
4.PC AUDIO INPUT: Connect the Audio output
jack of PC
5.VIDEO: Connect the Video output jack of DVD
or VCR
6.AUDIO LR INPUT: Connect the left and right
Audio output jacks of DVD or VCR for VIDEO /
S-VIDEO / YPbPr
7.S-VIDEO: Connect the S-VIDEO output jack
of DVD or VCR
1
2
3
4
5
6
7
4
4. TV INSTALLTION DRAWINGS
Power Cable Connection
Connect the power cord correctly as shown.
Press the POWER switch of your LCD VT to switch on the LCD TV. The power indicator on the front
panel lights up in green.
DC IN 12V
Connecting Antenna
VHF
ANTENNA
VHF
ANTENNA
OUTDOOR
ANTENNA
AMPLIFIER
INDOOR
ANTENNA
AMPLIFIER
75 OHM
ANTENNA
PLUG
POWER PLUG OF
ANTENNA
AMPLIFIER
To ensure good picture and sound, TV antenna system needs to be installed. The antenna system as
shown can be sourced from TV equipment shops, which will provide service for correct installation
and connection. After installation, insert the 75-ohm antenna plug into the antenna jack as shown.In
case of signal of closed circuit TV,
5
Video Connection
AUDIO L R IN
VIDEO IN
TV Back
AUDIO
DVD Back
Connect the VIDEO and AUDIO output jack of the DVD or VCR to the AV IN jacks on the set using
the RCA cable.
Select the AV input source with using the SOURCE button on the remote control.
S-Video Connection
TV Back
1
1
R
L
AUDIO
DVD Back
Connect the S-VIDEO output of the DVD or VCR to the S-VIDEO input on the set. The picture quality
is improved; compared to connecting a regular VCR to the video input. Connect the Audio output of the
DVD or VCR to the Audio input jacks on the set using the RCA cable.
Select S-VIDEO input source with using the SOURCE button on the remote control.
6
Y Pb Pr Connection
AUDIO L R IN
Y
PbPr IN
1
TV Back
Y
Pb Pr
L
R
DVD Back
Connect the YPbPr output of the DVD or VCR to the YPbPr input on the set. The picture quality is
improved; compared to connecting a regular VCR to the video input. Connect the Audio output of
the DVD or VCR to the Audio input jacks on the set using the RCA cable.
Select HD input source with using the SOURCE button on the remote control.
PC-RGB Connection
Stereo Audio Cable
RGB-PC OUTPUT AUDIO
P
I
VGA Cable
Connect the RGB output of the PC to the VGA in jack on the set Connect the PC AUDIO output of the
PC to the PC AUDIO in jack on the set Select the VGA input source with using SOURCE button.
7
5. REMOTE CONTROL FUNCTIONS
2
1
3
4
5
6.1 Remote control instructions in TV mode
1. POWER Switch on LCD TV when at standby mode or vice versa.
2.SOURCE Press to cycle through the input source in following.
3. MUTE Press to mute the sound. Press again or press V+ to unmated.
4. MENU Brings up the main menu to the screen.
5. THUMB STICK (▲/ ▼/ ◄ / ►/ ENTER) Allows you to navigate the on-screen menus and adjust
the system settings to your preference.
8
5.2 Battery Installation
a)Open the cover
b)AA size batteries, When inserting the batteries, make sure correct polarities as per”+“and ”-“marks
on the batteries and within the battery compartment
c)Replace the battery cover
5.3 Battery Usage Caution
To prevent battery leakage which may result in bodily injury or damage to the remote:
1.Install all batteries correctly, and as marked on the remote control.
2.Do not mix batteries:(OLD and NEW or CARBON and ALKALINE, etc)
3.Remove batteries when the remote is not used for a long time.
9
6. CONFIGURATION OF THE LCD
6.1 Enter picture menu
1. Press MENU key to open the main menu,
2. Press V-/+ to select:
3. Press V- enter setting picture menu, the outline border turns green.
4. Then press
5. After setting, press MENU to quit. Or wait for few seconds it will be quit automatically.
/
to select options in the picture menu
Brighness
Contrast
Colour
50
50
50
Sharpness
Preset
Normal
Personal
Options:
1. Brightness
Press V- to darken the picture.
Press V+ to brighten the picture.
2. Contrast
Press V- to decrease contrast
Press V+ to increase contrast
3. Colour
Press V- to decrease color intensity
Press V+ to increase color intensity
4. Sharpness
Press V- to soften the picture
Press V+ to sharpen the picture
5. Preset
Press V-/+ to select picture mode
Remark:
Personal
Soft
Standard
Dynamic
6.2 Enter sound menu
1. Press MENU key to open the main menu,
2. Press V-/+ to select:
3. Press V- enter setting sound menu, the outline border turns red.
4. Press to select option in the sound menu
5. After setting, press MENU to quit. Or wait for few seconds it will be quit automatically.
/
Options:
1. Volume
Press V- to decrease Volume
Press V+ to increase Volume
2. Mute
Volume
Mute
50
Off
When on is muting Volume
When off is closed it.
10
6.3 Enter Timer menu
1. Press MENU key to open the menu,
A
B
C
2. Press V-/+ in main menu to move menu bar, select
3. Press V- enters other setting menu.
4. Then press
5. After setting, press MENU to quit. Or wait for several seconds it will be quit automatically.
/
to select option in submenu
Option:
1. Clock
If you select clock, press0-9 to set time.
Clock
Reminder timer
Off time
Swith time
Off
2. Reminder timer
When get the right time, the TV will be off
automatically
If you select Reminder timer, press V-/+ to
select time
Remark:
Off
5
10 15
…
115 120
3. off timer
Press No. key to set the time when clock timer is the same as the off timer then power off the TV.
4. Switch timer,
If you select Switch timer, press No. key to set the time when you want to switch program
6.4 Enter other setting menu
1. Press MENU key to open the menu,
2. Press V-/+ in main menu to move menu bar, select
3. Press V- enters other setting menu.
4. Then press
/
to select option in submenu
5. After setting, press MENU to quit. Or wait for several seconds it will be quit automatically.
N o i s e R e d u c t i o n
L a n g u a g e
Off
E n g l i s h
Option:
1. Noise reduction
Press V-/+ to off/on the Noise reduction.
2. Language
Press V-/+ to select language
Remark:
English Francais Español
Portogués
Deutsch Italy
11
7. TROUBLESHOOTING AND ADVICE
Before calling our SAS centre, please check if you can solve the troubleshooting by yourself.
Troubleshooting
No signal
Control
Please check that all cables and cord's are correctly plugged in.
Adjust the contrast, the color and the brightness
No color shades
May be result from a lighting signal from car, motor, neon light and
other electrical devices or appliances.
Stain show on the
screen.
Double or multiple
display image
May be the result of an electrical wave disturb from other TV,
Computer and Game machine or Radio
The cables of the antenna are not correctly plugged in.
Snow on the screen
The remote control
does not work
Please check the batteries order and alignment.Check that the IR
of the remote control is not hidden by something.
Even if the display image is correct, the noise may come from an
unsteady fixation of the panel.
"Zip" made noise on
TV cover
Make sure that you have not press the MUTE button of the panel
or of the remote control.
No sound
12
8. SPECIFICATIONS
Screen Size
15 Inch
TFT LCD
1024 X 768
250cd/㎡
16.7M
Display Type
Resolution(Pixel)
Brightness
Color
450 : 1
Contrast Ratio
Aspect Ratio
4:3
Power Source
Video Input Format
Antenna Input
AC 100-240VAC, 50/60HZ DC 12V Adapter ≤60W
PAL / NTSC
Standard antenna socket 75Ω
L / R 3WX2
Audio Output
Video 1.0Vp-p 75 Ω; RCA
Y:1.0Vp-p 3db C:0.3Vp-p 3db
Video
S-Video
Input
800 600/60Hz 1024 600/60Hz 1280 1024/60Hz
R/L 200mVrms (max3.0vp-p) 20KΩ RCA
3 kgs
PC
Audio
(S-Video/Video/YPbPr/PC)
Weight
400(L) 360 (H) 130 (W) mm
Dimensions (with stand)
This manual is only for your reference, any change to the design and specification will not
be advised.
13
|